Wallpaper is posted at the moment, absolutely more with half the effort

There are many real estate renovation procedures and many details. It is comprehended that wallpaper construction may be the last procedure for hard decoration of the house decoration, the start of smooth decoration. Wallpapers ought to be completed in all hardware such as woodworking, paint, water and energy, plastering, and after a sanitary washing.

Flooring and skirting are installed
❖ Avoid smashing the keel, sawing solid wood, etc. when laying the floor to help make the wallpaper dirty.
❖ Avoid vibration when setting up the baseboard, which in turn causes the wallpaper to separate from the wall surface, leading to bubbling and curling of the wallpaper.
❖ Avoid a lot of dirt pollution and bruises when trimming the baseboard.
❖General putty will not be approved in the bottom of the wall, the first wallpaper can not be cut neatly, long time is prone to curling, leading to the wallpaper to roll-up.
❖ Avoid kicking the skirting series by sealing the wallpaper with glass glue, to ensure that the drinking water molecules in the wall structure can not be discharged, resulting in mildew of the baseboard.
Following the kicking line is installed, it is possible that the wall and the skirting line aren’t flat plenty of or have a gap. The post-installed wallpaper has the effect of within the gap.

Door cover and door are installed
First install the entranceway to avoid the wallpaper from being damaged and filthy, in fact it is also easy to repair the paint. If the wallpaper is normally patched and the paint is normally repaired (the gap between your door cover and the wall and the gap between your skirting lines) will stain the wallpaper.
How big is the card may vary. If the size is certainly too small, the wallpaper will end up being attached initial, and a blank will appear following the door is installed. If it’s full, it will very easily pull the wallpaper when the entranceway is installed, causing damage to the wallpaper.

Wood lacquer finish can not be wallpapered first, then real wood lacquer
❖Because the solid wood lacquer is sprayed during building, the paint will adhere to the wallpaper. And when the paint can be applied, the finished product should be shielded. In particular, the surrounding wall structure of the cabinet, door, partition, etc. should be protected with a protective film. If it is atomized to the wall structure surface, the building quality of the wallpaper isn’t guaranteed, in fact it is easy to cause problems.

Air conditioning hole is well
❖ Avoid punching and damage the wallpaper.
❖ Avoid wall vibration when punching, causing the wallpaper to fall off.
❖ Avoid dusting the wallpaper when punching.
Curtain rod hole is pre-made
The positioning of the curtain hanging rod support is well designed, and the hole is made to avoid the hole punching the top of wallpaper. Especially for flocking, silk, deep embossing, special materials and various other hard-to-care wallpapers, make sure to pre-attract the curtain rod holes before pasting.

How to paste wallpaper?
Remove the wall skin: take away the original paint and various other objects on the wall structure, use gypsum powder to fill the cracked area of the wall, and put a bandage after flattening; if it’s sand gray wall structure, partition wall, it should be covered with glass cloth Or indeed great cloth; some low quality partitions or external walls to attain the insulation effect, have to be filled with plasterboard

Cut the wallpaper: first gauge the height of the wall structure, then cut the length of the wallpaper, generally there are two kinds of cases: no flower wallpaper according to the elevation of the wall is cut about 5 to 8 cm duration, as the upper and reduce trimming: the flower wallpaper must consider the design symmetry Sex, therefore the amount of the cut should be increased based on the actual situation, generally 8 to 10 cm longer.

Applying glue: Apply the wallpaper glue to the trunk of the cut wallpaper with a brush, spend special attention to the surrounding edges to be coated with glue to guarantee the structure quality, the painted wallpaper, and the glue to face the fold. 5- ten minutes (remember that no external force should be put on prevent creases in the wallpaper, especially the cloth). After the glue is completely penetrated in to the paper, it can be posted, and several wallpapers are applied each time and posted to be able. Special material wallpaper must be glued on the wall, such as for example velvet sound-absorbing wallpaper, gold foil tin wallpaper, etc.

Wallpaper building: Generally, the first wallpaper is posted from the top to underneath of the door or the part of the corner. Utilize the squeegee throughout, from the inside to the outside, lightly scrape the wallpaper, Silk Wallpapers squeeze out the bubbles and extra glue to make the wallpaper smooth. Near to the wall.

Wallpaper building: Generally, the first wallpaper is posted from the top to the bottom of the entranceway or the part of the corner. Use the squeegee throughout, from the inside to the outside, lightly scrape the wallpaper, squeeze out the bubbles and excess glue to help make the wallpaper toned. Near to the wall.

Before wallpapering, turn off the power: When wallpapering, when you have a on / off switch or socket on the wall, you can turn off the main power, then cover the wallpaper with all the current power and socket, and cut two pairs from the center of gravity. The corner line will show four little triangles, and then utilize the utility knife to eliminate the extra wallpaper around.

Trimming and cleaning: Cut off the surplus wallpaper at the upper and decrease ends. The edge of the knife ought to be sharp in order to avoid burrs. When trimming some wall coverings, it is best to use a Japanese imported blade with a cost of just one 1.5 yuan. Then make use of a sponge dampened with drinking water to totally wipe the glue staying on the surface of the wallpaper to avoid the wallpaper from turning yellow. If the wallpaper can be dry following the wallpaper is dried out, make use of a knife to slice the injected glue and flatten it to eliminate it. it really is good)