The most common wallpaper problems and solutions!

When we put wallpapers, we often encounter problems like this. In particular, many of the friends who would like to do their personal wallpapers are a lot more than they need, and finally they will find there are always some small flaws.
In fact, provided that the construction is looked after, these problems could be avoided. Today, we will choose these problems and focus on solving them!
Base film peeling
1) Before brushing the bottom film, check whether the wall is standard, no powder, no floating level.
2) Is there a slight crack in the wall structure?
3) If the construction temperature is above 5 degrees.
4) Brush the bottom film too thick when it is initial, and brush the next one when it is not dry. Due to the difference in drying time taken between the inner and outer layers, it may cause peeling.
5) Whether the foundation film is too thick, can be relieved by adding drinking water. After polishing with sandpaper, re-brush the bottom film.
The treatment of the base film includes a great influence on the wallpaper effect, and the most direct effect may be the stability of the wallpaper. Therefore, the bottom film should be handled in accordance with certain requirements of the guidelines, combined with actual situation.
Glue overflow
Glue overflow is a common phenomenon along the way of wallpapering. During the construction process, stay away from the glue overflowing the wallpaper surface through the paper tape. The rubber surface area wallpaper is relatively simple to clean. You can use all of the wallpaper except the rubber tape wallpaper. Paper tape structure is recommended.
1) Wipe with a damp sponge for a surface area washable wallpaper.
2) Use a dry out towel to remove it, suitable for wallpapers that can’t be stained on the surface.
3) Absorbed with a wet sponge, ideal for wallpapers with contaminants on the surface.
There are signs at the joint seam
The handling of wallpaper seams has always been a key part of wallpaper construction, and many professional construction masters have their own tips. For the layman, pay special attention to the building. When the wallpaper was used, the glue did not completely hurry out and piled up at the seams. The glue reacted with the wallpaper for a long period.
Solution: 60-80 degrees boiling water a little bottle, plus a bottle of light vinegar, wait for the water to cool down, squat at the seam. (Recommended for partial tests), the wallpaper can last better in 1-2 months, and 80% of the traces can be removed.
Wallpaper shrinking
The phenomenon of wallpaper shrinkage is mainly caused by the workers’ lack of strict seams during construction, that leads to the problem in the later on stage, which is related to the construction technology of the workers. Since the wallpaper is made of wood pulp, it gets the characteristics of timber swelling and shrinking, the efficiency is not particularly stable, there will be a certain expansion after the glue is finished, and shrinkage occurs during the drying procedure. Although the growth is uncontrollable, workers can control shrinkage during building.
The majority of the wallpaper shrinks are invisible unless the joints aren’t enough. In this case, it is generally preferable to reserve a coincident portion at the joint. Generally, it is preferable that the joint overlaps at 1-3 cm.
If shrinkage has recently occurred, the repair procedure is relatively simple. Make use of a wet towel dampened with water to soak the seam for ten minutes, and use the edge of the wallpaper knife to pick the wallpaper, that may usually be picked up. If the attachment on the surface of the wallpaper is a metal surface, it is easy to make the top of wallpaper tarnish and dark after scraping, and it is not really recommended to operate.
Wallpaper moldy
1) The wallpaper is moldy and generally provides spots on the surface of the wallpaper.
(1) The wall ought to be inspected for water seepage.
(2) If the glue is completely dry.
(3)When wallpaper is usually applied, whether moisture and air are present in the wallpaper for a long period, react with the glue to cause mold.
(4) The weather is humid.
(5) The wallpaper is wet.
Moldy wallpaper is certainly a problem that people who are wallpapering come to mind about. Additionally it is probably the most difficult complications to solve after emergence. Therefore, this kind of issue should be predicated on prevention. It is advisable to work in front of moisture and moisture.
Then, following the wallpaper offers such problems, will there be no solution? of program not.
2) Processing 3D Wallcoverings method
(1) The mildew is small. It is suggested to wipe with drinking water or detergent and blow dry with a locks dryer.
(2) Bleaching water is definitely easy to irritate the pores and skin and may cause the wallpaper to fade. It is not recommended.
(3) If the mold is large, the wallpaper needs to be replaced. If the wall is seepage, it’s important to completely solve the issue before posting.